date BS EN is withdrawn and BS EN and BS EN In addition IEC and IEC have been amended, clarified and. For each type of electrical AssEMBLY only two parts of the standard are necessary to determine all requirements: the basic standard IEC “ General rules. What changes does BS EN bring? • New testing procedure including design and routine verification. • Alternative testing routes. • Clear requirements for.
|Published (Last):||2 March 2005|
|PDF File Size:||20.80 Mb|
|ePub File Size:||14.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
The selection of the appropriate verification methods is the 61439–1 of the original manufacturer. Date Text affectedLicensed Copy: For more explanation see Certification tests have been performed on the lifting beams that we manufacture; these can be reviewed during CFAT and prior to despatch.
614391- If a set of busbars consists of different sections as regards cross-sections, distance between adjacent busbars, type and number of supports per metreeach section shall be tested separately or concurrently, provided that the above conditions are met. If identification by colour only is used, it shall be blue see IEC This clause of Part 1 is applicable except as follows. Fuse-link power loss may be determined by measurement or alternatively as declared by the fuse-link manufacturer.
In general, auxiliary circuits shall be hs against the effects of short circuits.
For details of requirements for terminals for external protective conductors, see 8. The power losses of the conductors 61439-11 determined by calculation see Annex H. The enclosure, mounted as for normal use, is subjected to a test in a heating cabinet with an atmosphere having the composition and pressure of the ambient air and ventilated by natural circulation.
NOTE Ability to withstand a particularly high test voltage is recognized as a means of ensuring the necessary degree of isolation.
Clearances shall be verified by measurement, or verification of measurements on design drawings, employing the measurement methods stated in Annex F. No changes to visible display information Temporary visible changes Permanent loss of display or Operation of displays or loss of information. Compliance to this requirement is checked by the test of A list of organizations represented on this committee can be obtained onrequest to its secretary.
However, the specified degree of protection shall at the same time be maintained. Exposed conductive parts of a device that cannot be connected to the protective circuit by the fixing means of the device shall be connected to the protective circuit of the ASSEMBLY by a conductor whose cross-sectional area is chosen according to Table 3.
All other parts e. General rules 3 Terms and definitions This clause of Part 1 is applicable except as follows. This ensures that additional thermal effects relating to eddy currents and current displacement are taken into consideration.
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
The power losses can then be calculated by the same method as used for this Table H. NOTE 2 Transients are disregarded.
Such conductors shall not be connected to the protective conductors or exposed-conductive-parts of other circuits or to any extraneous conductive parts. NOTE 3 It is the value to which dielectric test voltages and creepage distances are referred, see also 8. If the main busbar has joints, then they shall be included in the test. It applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below.
This part of IEC lays down the definitions and states the service conditions, construction requirements, technical characteristics and verification requirements for low-voltage switchgear and controlgear assemblies. Protection for safety – Protection against voltage disturbances and electromagnetic disturbances IEC Electrical installations of buildings – – – Part Use of this product in environment B may cause unwanted electromagnetic disturbances in which case the user may be required to take adequate mitigation measures.
It presents the UK view on standards in Europe and at the international level. The environments encompassed are residential, commercial and light-industrial locations, both indoor and outdoor.
For details of these and other benefits contact Membership Ad-Email: The rated diversity factor multiplied by the rated current of the circuits shall be equal to or higher than the assumed loading of the outgoing circuits.
For protection, by total insulation, against indirect contact the following requirements shall be met. X mm wide on each side.
614339-1 test voltage tolerances and the selection of test equipment, see IEC Paints, varnishes and lacquers alone are not considered to satisfy the requirements for basic insulation. When the protective device in the outgoing circuit is a circuit-breaker, the test circuit may include a shunting resistor in accordance with 8.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.